Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-CURRENT #1: Tue Apr 21 11:34:47 CEST 2009
    guru@vm-naranja.Sisis.de:/usr/obj/usr/src/sys/GENERIC
WARNING: WITNESS option enabled, expect reduced performance.
Preloaded elf kernel "/boot/kernel/kernel" at 0xc10a7000.
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 3059027922 Hz
CPU: Intel(R) Core(TM)2 Extreme CPU X9100  @ 3.06GHz (3059.03-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x10676  Stepping = 6
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x8e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1>
  AMD Features=0x20100000<NX,LM>
  AMD Features2=0x1<LAHF>
  TSC: P-state invariant
  Cores per package: 2

Instruction TLB: 4 KB Pages, 4-way set associative, 128 entries
1st-level instruction cache: 32 KB, 8-way set associative, 64 byte line size
1st-level data cache: 32 KB, 8-way set associative, 64 byte line size
L2 cache: 6144 kbytes, 16-way associative, 64 bytes/line
real memory  = 3745845248 (3572 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009afff, 630784 bytes (154 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000001425000 - 0x00000000db89cfff, 3662118912 bytes (894072 pages)
avail memory = 3660681216 (3491 MB)
Table 'FACP' at 0xdf45449c
Table 'HPET' at 0xdf454700
Table '____' at 0xdf462c00
Table 'APIC' at 0xdf454800
MADT: Found table at 0xdf454800
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 0: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 1 ACPI ID 1: enabled
SMP: Added CPU 1 (AP)
MADT: Found CPU APIC ID 2 ACPI ID 2: disabled
MADT: Found CPU APIC ID 3 ACPI ID 3: disabled
ACPI APIC Table: <DELL   M09    >
INTR: Adding local APIC 1 as a target
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
APIC: CPU 0 has ACPI ID 0
APIC: CPU 1 has ACPI ID 1
bios32: Found BIOS32 Service Directory header at 0xc00ffa00
bios32: Entry = 0xffa10 (c00ffa10)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xa7f6
pnpbios: Found PnP BIOS data at 0xc00fe2d0
pnpbios: Entry = f0000:e2f4  Rev = 1.0
pnpbios: Event flag at 4b4
Other BIOS signatures found:
ULE: setup cpu 0
ULE: setup cpu 1
ACPI: RSDP @ 0x0xfb9b0/0x0024 (v  2 DELL  )
ACPI: XSDT @ 0x0xdf454600/0x006C (v  1 DELL    M09     0x27D90317 ASL  0x00000061)
ACPI: FACP @ 0x0xdf45449c/0x00F4 (v  4 DELL    M09     0x27D90317 ASL  0x00000061)
ACPI: DSDT @ 0x0xdf454c00/0x5AD4 (v  2 INT430 SYSFexxx 0x00001001 INTL 0x20050624)
ACPI: FACS @ 0x0xdf463400/0x0040
ACPI: HPET @ 0x0xdf454700/0x0038 (v  1 DELL    M09     0x00000001 ASL  0x00000061)
ACPI: ____ @ 0x0xdf462c00/0x0030 (v  1 DELL    M09     0x27D90317 ASL  0x00000061)
ACPI: APIC @ 0x0xdf454800/0x0078 (v  1 DELL    M09     0x27D90317 ASL  0x00000047)
ACPI: ASF! @ 0x0xdf454400/0x006A (v 32 DELL    M09     0x27D90317 ASL  0x00000061)
ACPI: MCFG @ 0x0xdf4547c0/0x003E (v 16 DELL    M09     0x27D90317 ASL  0x00000061)
ACPI: TCPA @ 0x0xdf454b00/0x0032 (v  1                 0x00000000 ASL  0x00000000)
ACPI: SLIC @ 0x0xdf45489c/0x0176 (v  1 DELL    M09     0x27D90317 ASL  0x00000061)
ACPI: SSDT @ 0x0xdf452b2d/0x066C (v  1  PmRef    CpuPm 0x00003000 INTL 0x20050624)
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: Changing APIC ID to 2
ioapic0: Routing external 8259A's -> intpin 0
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: high
lapic1: Routing NMI -> LINT1
lapic1: LINT1 trigger: edge
lapic1: LINT1 polarity: high
ioapic0 <Version 2.0> irqs 0-23 on motherboard
cpu0 BSP:
     ID: 0x00000000   VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000100ef therm: 0x00010000 err: 0x00010000 pcm: 0x00000400
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
io: <I/O>
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
Pentium Pro MTRR support enabled
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2 (Apr 21 2009 11:34:27)
npx0: INT 16 interface
acpi0: <DELL M09    > on motherboard
PCIe: Memory Mapped configuration base @ 0xf8000000
pcibios: BIOS version 2.10
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48
acpi0: [MPSAFE]
acpi0: [ITHREAD]
acpi0: wakeup code va 0xc6cc9000 pa 0x1000
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.ISAB.PIR1 -> bus 0 dev 31 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.ISAB.PIR2 -> bus 0 dev 31 func 0
acpi_hpet0: vend: 0x8086 rev: 0x1 num: 3 hz: 14318180 opts: legacy_route 64-bit
Timecounter "HPET" frequency 14318180 Hz quality 900
acpi0: reservation of 0, 9f000 (3) failed
acpi0: reservation of 100000, df351c00 (3) failed
ACPI timer: 1/2 1/2 1/2 1/2 1/1 1/1 1/2 1/2 1/1 1/2 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x11> port 0x930,0x934 on acpi0
pci_link0:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    3   N     0  10 11
  Validation          0  255   N     0  10 11
  After Disable       0  255   N     0  10 11
pci_link1:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   10   N     0  5 7
  Validation          0  255   N     0  5 7
  After Disable       0  255   N     0  5 7
pci_link2:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   11   N     0  10 11
  Validation          0   11   N     0  10 11
  After Disable       0  255   N     0  10 11
pci_link3:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   10   N     0  5 7 10 11
  Validation          0   10   N     0  5 7 10 11
  After Disable       0  255   N     0  5 7 10 11
pci_link4:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   10   N     0  3 4 5 6 7 10 11 12 14 15
  Validation          0   10   N     0  3 4 5 6 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 6 7 10 11 12 14 15
pci_link5:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    3   N     0  3 4 5 6 7 10 11 12 14 15
  Validation          0    3   N     0  3 4 5 6 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 6 7 10 11 12 14 15
pci_link6:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   11   N     0  3 4 5 6 7 10 11 12 14 15
  Validation          0   11   N     0  3 4 5 6 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 6 7 10 11 12 14 15
pci_link7:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  3 4 5 6 7 10 11 12 14 15
  Validation          0  255   N     0  3 4 5 6 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 6 7 10 11 12 14 15
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found->	vendor=0x8086, dev=0x2a40, revid=0x07
	domain=0, bus=0, slot=0, func=0
	class=06-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x8086, dev=0x2a41, revid=0x07
	domain=0, bus=0, slot=1, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x1a (6500 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=255
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
found->	vendor=0x8086, dev=0x10f5, revid=0x03
	domain=0, bus=0, slot=25, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0107, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D3  current D0
	MSI supports 1 message, 64 bit
	map[10]: type Memory, range 32, base 0xf6fe0000, size 17, enabled
	map[14]: type Memory, range 32, base 0xf6fdb000, size 12, enabled
	map[18]: type I/O Port, range 32, base 0xefe0, size  5, enabled
pcib0: matched entry for 0.25.INTA
pcib0: slot 25 INTA hardwired to IRQ 22
found->	vendor=0x8086, dev=0x2937, revid=0x03
	domain=0, bus=0, slot=26, func=0
	class=0c-03-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	map[20]: type I/O Port, range 32, base 0x6f60, size  5, enabled
pcib0: matched entry for 0.26.INTA
pcib0: slot 26 INTA hardwired to IRQ 20
found->	vendor=0x8086, dev=0x2938, revid=0x03
	domain=0, bus=0, slot=26, func=1
	class=0c-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=3
	map[20]: type I/O Port, range 32, base 0x6f80, size  5, enabled
pcib0: matched entry for 0.26.INTB
pcib0: slot 26 INTB hardwired to IRQ 21
found->	vendor=0x8086, dev=0x2939, revid=0x03
	domain=0, bus=0, slot=26, func=2
	class=0c-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=c, irq=11
	map[20]: type I/O Port, range 32, base 0x6fa0, size  5, enabled
pcib0: matched entry for 0.26.INTC
pcib0: slot 26 INTC hardwired to IRQ 22
found->	vendor=0x8086, dev=0x293c, revid=0x03
	domain=0, bus=0, slot=26, func=7
	class=0c-03-20, hdrtype=0x00, mfdev=0
	cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=c, irq=11
	powerspec 2  supports D0 D3  current D0
	map[10]: type Memory, range 32, base 0xfed1c400, size 10, enabled
pcib0: matched entry for 0.26.INTC
pcib0: slot 26 INTC hardwired to IRQ 22
found->	vendor=0x8086, dev=0x293e, revid=0x03
	domain=0, bus=0, slot=27, func=0
	class=04-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0106, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=3
	powerspec 2  supports D0 D3  current D0
	MSI supports 1 message, 64 bit
	map[10]: type Memory, range 64, base 0xf6fdc000, size 14, enabled
pcib0: matched entry for 0.27.INTA
pcib0: slot 27 INTA hardwired to IRQ 21
found->	vendor=0x8086, dev=0x2940, revid=0x03
	domain=0, bus=0, slot=28, func=0
	class=06-04-00, hdrtype=0x01, mfdev=1
	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=255
	powerspec 2  supports D0 D3  current D0
	MSI supports 1 message
found->	vendor=0x8086, dev=0x2942, revid=0x03
	domain=0, bus=0, slot=28, func=1
	class=06-04-00, hdrtype=0x01, mfdev=1
	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=255
	powerspec 2  supports D0 D3  current D0
	MSI supports 1 message
found->	vendor=0x8086, dev=0x2944, revid=0x03
	domain=0, bus=0, slot=28, func=2
	class=06-04-00, hdrtype=0x01, mfdev=1
	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
	intpin=c, irq=255
	powerspec 2  supports D0 D3  current D0
	MSI supports 1 message
found->	vendor=0x8086, dev=0x2946, revid=0x03
	domain=0, bus=0, slot=28, func=3
	class=06-04-00, hdrtype=0x01, mfdev=1
	cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
	intpin=d, irq=255
	powerspec 2  supports D0 D3  current D0
	MSI supports 1 message
found->	vendor=0x8086, dev=0x2934, revid=0x03
	domain=0, bus=0, slot=29, func=0
	class=0c-03-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	map[20]: type I/O Port, range 32, base 0x6f00, size  5, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 20
found->	vendor=0x8086, dev=0x2935, revid=0x03
	domain=0, bus=0, slot=29, func=1
	class=0c-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=3
	map[20]: type I/O Port, range 32, base 0x6f20, size  5, enabled
pcib0: matched entry for 0.29.INTB
pcib0: slot 29 INTB hardwired to IRQ 21
found->	vendor=0x8086, dev=0x2936, revid=0x03
	domain=0, bus=0, slot=29, func=2
	class=0c-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=c, irq=11
	map[20]: type I/O Port, range 32, base 0x6f40, size  5, enabled
pcib0: matched entry for 0.29.INTC
pcib0: slot 29 INTC hardwired to IRQ 22
found->	vendor=0x8086, dev=0x293a, revid=0x03
	domain=0, bus=0, slot=29, func=7
	class=0c-03-20, hdrtype=0x00, mfdev=0
	cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 2  supports D0 D3  current D0
	map[10]: type Memory, range 32, base 0xfed1c000, size 10, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 20
found->	vendor=0x8086, dev=0x2448, revid=0x93
	domain=0, bus=0, slot=30, func=0
	class=06-04-01, hdrtype=0x01, mfdev=0
	cmdreg=0x0107, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
found->	vendor=0x8086, dev=0x2917, revid=0x03
	domain=0, bus=0, slot=31, func=0
	class=06-01-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0107, statreg=0x0210, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x8086, dev=0x282a, revid=0x03
	domain=0, bus=0, slot=31, func=2
	class=01-04-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=d, irq=10
	powerspec 3  supports D0 D3  current D0
	MSI supports 16 messages
	map[10]: type I/O Port, range 32, base 0x6e70, size  3, enabled
	map[14]: type I/O Port, range 32, base 0x6e78, size  2, enabled
	map[18]: type I/O Port, range 32, base 0x6e80, size  3, enabled
	map[1c]: type I/O Port, range 32, base 0x6e88, size  2, enabled
	map[20]: type I/O Port, range 32, base 0x6ea0, size  5, enabled
	map[24]: type Memory, range 32, base 0xfed1c800, size 11, enabled
pcib0: matched entry for 0.31.INTD
pcib0: slot 31 INTD hardwired to IRQ 19
found->	vendor=0x8086, dev=0x2930, revid=0x03
	domain=0, bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0103, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=10
	map[10]: type Memory, range 64, base 0xf6fdaf00, size  8, enabled
	map[20]: type I/O Port, range 32, base 0x1100, size  5, enabled
pcib0: matched entry for 0.31.INTB
pcib0: slot 31 INTB hardwired to IRQ 19
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1:   domain            0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0xd000-0xdfff
pcib1:   memory decode     0xf2000000-0xf6efffff
pcib1:   prefetched decode 0xe0000000-0xefffffff
pci1: <ACPI PCI bus> on pcib1
pci1: domain=0, physical bus=1
found->	vendor=0x10de, dev=0x065c, revid=0xa1
	domain=0, bus=1, slot=0, func=0
	class=03-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=3
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit
	map[10]: type Memory, range 32, base 0xf5000000, size 24, enabled
pcib1: requested memory range 0xf5000000-0xf5ffffff: good
	map[14]: type Prefetchable Memory, range 64, base 0xe0000000, size 28, enabled
pcib1: requested memory range 0xe0000000-0xefffffff: good
	map[1c]: type Memory, range 64, base 0xf2000000, size 25, enabled
pcib1: requested memory range 0xf2000000-0xf3ffffff: good
	map[24]: type I/O Port, range 32, base 0xdf00, size  7, enabled
pcib1: requested I/O range 0xdf00-0xdf7f: in range
pcib1: matched entry for 1.0.INTA
pcib1: slot 0 INTA hardwired to IRQ 16
vgapci0: <VGA-compatible display> port 0xdf00-0xdf7f mem 0xf5000000-0xf5ffffff,0xe0000000-0xefffffff,0xf2000000-0xf3ffffff irq 16 at device 0.0 on pci1
em0: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0xefe0-0xefff mem 0xf6fe0000-0xf6ffffff,0xf6fdb000-0xf6fdbfff irq 22 at device 25.0 on pci0
em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xf6fe0000
em0: attempting to allocate 1 MSI vectors (1 supported)
em0: using IRQ 256 for MSI
em0: Using MSI interrupt
em0: Reserved 0x1000 bytes for rid 0x14 type 3 at 0xf6fdb000
msi: Assigning MSI IRQ 256 to local APIC 0 vector 49
em0: [FILTER]
em0: bpf attached
em0: Ethernet address: 00:21:70:f3:54:c5
uhci0: <Intel 82801I (ICH9) USB controller> port 0x6f60-0x6f7f irq 20 at device 26.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x6f60
ioapic0: routing intpin 20 (PCI IRQ 20) to lapic 0 vector 50
uhci0: [MPSAFE]
uhci0: [ITHREAD]
uhci0: LegSup = 0x0f00
usbus0: <Intel 82801I (ICH9) USB controller> on uhci0
uhci1: <Intel 82801I (ICH9) USB controller> port 0x6f80-0x6f9f irq 21 at device 26.1 on pci0
uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0x6f80
ioapic0: routing intpin 21 (PCI IRQ 21) to lapic 0 vector 51
uhci1: [MPSAFE]
uhci1: [ITHREAD]
uhci1: LegSup = 0x0f00
usbus1: <Intel 82801I (ICH9) USB controller> on uhci1
uhci2: <Intel 82801I (ICH9) USB controller> port 0x6fa0-0x6fbf irq 22 at device 26.2 on pci0
uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0x6fa0
ioapic0: routing intpin 22 (PCI IRQ 22) to lapic 0 vector 52
uhci2: [MPSAFE]
uhci2: [ITHREAD]
uhci2: LegSup = 0x0f00
usbus2: <Intel 82801I (ICH9) USB controller> on uhci2
ehci0: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xfed1c400-0xfed1c7ff irq 22 at device 26.7 on pci0
ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xfed1c400
ehci0: [MPSAFE]
ehci0: [ITHREAD]
usbus3: EHCI version 1.0
usbus3: <Intel 82801I (ICH9) USB 2.0 controller> on ehci0
pci0: <multimedia, HDA> at device 27.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pcib2:   domain            0
pcib2:   secondary bus     11
pcib2:   subordinate bus   11
pcib2:   I/O decode        0xf000-0xfff
pcib2:   no prefetched decode
pci11: <ACPI PCI bus> on pcib2
pci11: domain=0, physical bus=11
pcib3: <ACPI PCI-PCI bridge> at device 28.1 on pci0
pcib3:   domain            0
pcib3:   secondary bus     12
pcib3:   subordinate bus   12
pcib3:   I/O decode        0xf000-0xfff
pcib3:   memory decode     0xf1f00000-0xf1ffffff
pcib3:   no prefetched decode
pci12: <ACPI PCI bus> on pcib3
pci12: domain=0, physical bus=12
found->	vendor=0x14e4, dev=0x432b, revid=0x01
	domain=0, bus=12, slot=0, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0106, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 3  supports D0 D1 D2 D3  current D0
	MSI supports 1 message, 64 bit
	map[10]: type Memory, range 64, base 0xf1ffc000, size 14, enabled
pcib3: requested memory range 0xf1ffc000-0xf1ffffff: good
pcib3: matched entry for 12.0.INTA
pcib3: slot 0 INTA hardwired to IRQ 17
pci12: <network> at device 0.0 (no driver attached)
pcib4: <ACPI PCI-PCI bridge> at device 28.2 on pci0
pcib4:   domain            0
pcib4:   secondary bus     13
pcib4:   subordinate bus   13
pcib4:   I/O decode        0xf000-0xfff
pcib4:   no prefetched decode
pci13: <ACPI PCI bus> on pcib4
pci13: domain=0, physical bus=13
pcib5: <ACPI PCI-PCI bridge> at device 28.3 on pci0
pcib5:   domain            0
pcib5:   secondary bus     14
pcib5:   subordinate bus   15
pcib5:   I/O decode        0xc000-0xcfff
pcib5:   memory decode     0xf1c00000-0xf1efffff
pcib5:   prefetched decode 0xf0000000-0xf01fffff
pci14: <ACPI PCI bus> on pcib5
pci14: domain=0, physical bus=14
uhci3: <Intel 82801I (ICH9) USB controller> port 0x6f00-0x6f1f irq 20 at device 29.0 on pci0
uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0x6f00
uhci3: [MPSAFE]
uhci3: [ITHREAD]
uhci3: LegSup = 0x0f00
usbus4: <Intel 82801I (ICH9) USB controller> on uhci3
uhci4: <Intel 82801I (ICH9) USB controller> port 0x6f20-0x6f3f irq 21 at device 29.1 on pci0
uhci4: Reserved 0x20 bytes for rid 0x20 type 4 at 0x6f20
uhci4: [MPSAFE]
uhci4: [ITHREAD]
uhci4: LegSup = 0x0f00
usbus5: <Intel 82801I (ICH9) USB controller> on uhci4
uhci5: <Intel 82801I (ICH9) USB controller> port 0x6f40-0x6f5f irq 22 at device 29.2 on pci0
uhci5: Reserved 0x20 bytes for rid 0x20 type 4 at 0x6f40
uhci5: [MPSAFE]
uhci5: [ITHREAD]
uhci5: LegSup = 0x0f00
usbus6: <Intel 82801I (ICH9) USB controller> on uhci5
ehci1: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xfed1c000-0xfed1c3ff irq 20 at device 29.7 on pci0
ehci1: Reserved 0x400 bytes for rid 0x10 type 3 at 0xfed1c000
ehci1: [MPSAFE]
ehci1: [ITHREAD]
usbus7: EHCI version 1.0
usbus7: <Intel 82801I (ICH9) USB 2.0 controller> on ehci1
pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib6:   domain            0
pcib6:   secondary bus     3
pcib6:   subordinate bus   4
pcib6:   I/O decode        0xf000-0xfff
pcib6:   memory decode     0xf1b00000-0xf1bfffff
pcib6:   no prefetched decode
pcib6:   Subtractively decoded bridge.
pci3: <ACPI PCI bus> on pcib6
pci3: domain=0, physical bus=3
found->	vendor=0x1180, dev=0x0476, revid=0xba
	domain=0, bus=3, slot=1, func=0
	class=06-07-00, hdrtype=0x02, mfdev=1
	cmdreg=0x0107, statreg=0x0210, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x07 (1750 ns)
	intpin=a, irq=10
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type Memory, range 32, base 0, size 12, enabled
pcib6: matched entry for 3.1.INTA
pcib6: slot 1 INTA hardwired to IRQ 19
found->	vendor=0x1180, dev=0x0832, revid=0x04
	domain=0, bus=3, slot=1, func=1
	class=0c-00-10, hdrtype=0x00, mfdev=1
	cmdreg=0x0106, statreg=0x0210, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
	intpin=b, irq=10
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type Memory, range 32, base 0xf1bff800, size 11, enabled
pcib6: requested memory range 0xf1bff800-0xf1bfffff: good
pcib6: matched entry for 3.1.INTB
pcib6: slot 1 INTB hardwired to IRQ 17
found->	vendor=0x1180, dev=0x0822, revid=0x21
	domain=0, bus=3, slot=1, func=2
	class=08-05-01, hdrtype=0x00, mfdev=1
	cmdreg=0x0106, statreg=0x0210, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=c, irq=11
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type Memory, range 32, base 0xf1bff600, size  8, enabled
pcib6: requested memory range 0xf1bff600-0xf1bff6ff: good
pcib6: matched entry for 3.1.INTC
pcib6: slot 1 INTC hardwired to IRQ 18
found->	vendor=0x1180, dev=0x0843, revid=0x11
	domain=0, bus=3, slot=1, func=3
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0106, statreg=0x0210, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=c, irq=11
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type Memory, range 32, base 0xf1bff700, size  8, enabled
pcib6: requested memory range 0xf1bff700-0xf1bff7ff: good
pcib6: matched entry for 3.1.INTC
pcib6: slot 1 INTC hardwired to IRQ 18
cbb0: <RF5C476 PCI-CardBus Bridge> irq 19 at device 1.0 on pci3
pcib6: cbb0 requested memory range 0x0-0xffffffff: good
cbb0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0xf0000000
cbb0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xf0000000
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 0 vector 53
cbb0: [MPSAFE]
cbb0: [FILTER]
cbb0: Bad Vcc requested
cbb0: PCI Configuration space:
  0x00: 0x04761180 0x02100107 0x060700ba 0x00824000 
  0x10: 0xf0000000 0x020000dc 0x20040403 0xfffff000 
  0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc 
  0x30: 0x00000000 0xfffffffc 0x00000000 0x07800113 
  0x40: 0x02501028 0x00000001 0x00000000 0x00000000 
  0x50: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x60: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x70: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x80: 0x30a00001 0x00000000 0x04630463 0x00000000 
  0x90: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xa0: 0x00000008 0x00000000 0x00000000 0x00000000 
  0xb0: 0x00000000 0xb0000000 0x00003000 0x00000000 
  0xc0: 0x02501028 0x00000000 0x00000000 0x00000000 
  0xd0: 0x00000000 0x00000000 0x00000000 0xfe0a0001 
  0xe0: 0x24c04000 0x00000000 0x00000000 0x00000000 
  0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 
fwohci0: vendor=1180, dev=832
fwohci0: vendor=1180, dev=832
fwohci0: <1394 Open Host Controller Interface> mem 0xf1bff800-0xf1bfffff irq 17 at device 1.1 on pci3
fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xf1bff800
ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 0 vector 54
fwohci0: [MPSAFE]
fwohci0: [ITHREAD]
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 43:4f:c0:00:01:29:24:90
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x14a8000
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 42:4f:c0:29:24:90
fwe0: bpf attached
fwe0: Ethernet address: 42:4f:c0:29:24:90
fwip0: <IP over FireWire> on firewire0
fwip0: bpf attached
fwip0: Firewire address: 43:4f:c0:00:01:29:24:90 @ 0xfffe00000000, S400, maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: fwohci_intr_core: BUS reset
fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, CYCLEMASTER mode
pci3: <base peripheral, SD host controller> at device 1.2 (no driver attached)
pci3: <base peripheral> at device 1.3 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH8M SATA300 controller> port 0x6e70-0x6e77,0x6e78-0x6e7b,0x6e80-0x6e87,0x6e88-0x6e8b,0x6ea0-0x6ebf mem 0xfed1c800-0xfed1cfff irq 19 at device 31.2 on pci0
atapci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x6ea0
atapci0: [MPSAFE]
atapci0: [ITHREAD]
atapci0: Reserved 0x800 bytes for rid 0x24 type 3 at 0xfed1c800
atapci0: AHCI called from vendor specific driver
atapci0: AHCI Version 01.20 controller with 4 ports PM supported
ata2: <ATA channel 0> on atapci0
ata2: AHCI reset...
ata2: SATA connect time=0ms
ata2: ready wait time=65ms
ata2: software reset port 15...
ata2: ready wait time=0ms
ata2: SIGNATURE: 00000101
ata2: AHCI reset done: devices=00000001
ata2: [MPSAFE]
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: AHCI reset...
ata3: SATA connect time=0ms
ata3: ready wait time=0ms
ata3: software reset port 15...
ata3: ready wait time=0ms
ata3: SIGNATURE: eb140101
ata3: AHCI reset done: devices=00010000
ata3: [MPSAFE]
ata3: [ITHREAD]
ata4: <ATA channel 4> on atapci0
ata4: AHCI reset...
ata4: SATA connect status=00000000
ata4: AHCI reset done: phy reset found no device
ata4: [MPSAFE]
ata4: [ITHREAD]
ata5: <ATA channel 5> on atapci0
ata5: AHCI reset...
ata5: SATA connect status=00000000
ata5: AHCI reset done: phy reset found no device
ata5: [MPSAFE]
ata5: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
battery1: <ACPI Control Method Battery> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64,0x62,0x66 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 55
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 0 vector 56
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model GlidePoint, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000008, packet size:3
psm0: syncmask:c0, syncbits:00
atrtc0: <AT realtime clock> port 0x70-0x71,0x72-0x77 irq 8 on acpi0
atrtc0: registered as a time-of-day clock (resolution 1000000us)
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 0 vector 57
uart0: [FILTER]
uart0: fast interrupt
ppc0: using extended I/O port range
ppc0: SPP ECP  ECP+EPP
ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77b irq 7 drq 1 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/7 bytes threshold
ioapic0: routing intpin 7 (ISA IRQ 7) to lapic 0 vector 58
ppc0: [MPSAFE]
ppc0: [ITHREAD]
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
plip0: [MPSAFE]
plip0: [ITHREAD]
lpt0: <Printer> on ppbus0
lpt0: [MPSAFE]
lpt0: [ITHREAD]
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
cpu0: <ACPI CPU> on acpi0
ACPI: SSDT @ 0x0xdf453199/0x0281 (v  1  PmRef   BspIst 0x00003000 INTL 0x20050624)
ACPI: SSDT @ 0x0xdf4535f1/0x05C6 (v  1  PmRef   BspCst 0x00003001 INTL 0x20050624)
ACPI Error (dsopcode-0350): No pointer back to NS node in buffer obj 0xc72eb080 [20070320]
ACPI Exception (dswexec-0556): AE_AML_INTERNAL, While resolving operands for [OpcodeName unavailable] [20070320]
ACPI Error (psparse-0626): Method parse/execution failed [\\_PR_.CPU0._OSC] (Node 0xc72c9340), AE_AML_INTERNAL
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est0: Invalid id16 (set, cur) = (2081, 2858)
est0: Invalid freq 2134, ignored.
est0: Invalid id16 (set, cur) = (1563, 2858)
est0: Invalid freq 1600, ignored.
est0: Invalid id16 (set, cur) = (34327, 2858)
est0: Invalid freq 800, ignored.
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
ACPI: SSDT @ 0x0xdf45341a/0x01D7 (v  1  PmRef    ApIst 0x00003000 INTL 0x20050624)
ACPI: SSDT @ 0x0xdf453bb7/0x008D (v  1  PmRef    ApCst 0x00003000 INTL 0x20050624)
ACPI Error (dsopcode-0350): No pointer back to NS node in buffer obj 0xc72e8cc0 [20070320]
ACPI Exception (dswexec-0556): AE_AML_INTERNAL, While resolving operands for [OpcodeName unavailable] [20070320]
ACPI Error (psparse-0626): Method parse/execution failed [\\_PR_.CPU1._OSC] (Node 0xc72c9260), AE_AML_INTERNAL
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est1: Invalid id16 (set, cur) = (2081, 2858)
est1: Invalid freq 2134, ignored.
est1: Invalid id16 (set, cur) = (1563, 2858)
est1: Invalid freq 1600, ignored.
est1: Invalid id16 (set, cur) = (34327, 2858)
est1: Invalid freq 800, ignored.
p4tcc1: <CPU Frequency Thermal Control> on cpu1
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ahc_isa_probe 0: ioport 0xc00 alloc failed
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
ex_isa_identify()
isa_probe_children: disabling PnP devices
pmtimer0 on isa0
atkbdc: atkbdc0 already exists; skipping it
atrtc: atrtc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sc: sc0 already exists; skipping it
uart: uart0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcdfff,0xce000-0xd2fff,0xd3000-0xd3fff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: reset tp1 mask=00 ostat0=ff ostat1=ff
ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 0 vector 59
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ioapic0: routing intpin 15 (ISA IRQ 15) to lapic 0 vector 60
ata1: [MPSAFE]
ata1: [ITHREAD]
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
sn0: not probed (disabled)
uart1: <ns8250> failed to probe at port 0x2f8-0x2ff irq 3 on isa0
uart2: not probed (disabled)
uart3: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
Reducing kern.maxvnodes 229912 -> 100000
procfs registered
lapic: Divisor 2, Frequency 133001224 hz
Timecounter "TSC" frequency 3059027922 Hz quality -100
Timecounters tick every 1.000 msec
lo0: bpf attached
hptrr: nofirewire0: 1 nodes, maxhop <= 0 cable IRM irm(0)  (me) 
firewire0: bus manager 0 
 controller detected.
ata0: Identifying devices: 00000000
ata0: New devices: 00000000
ata1: Identifying devices: 00000000
ata1: New devices: 00000000
ata2: Identifying devices: 00000001
ata2: New devices: 00000001
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
acpi_acad0: acline initialization start
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
battery0: battery initialization start
battery1: battery initialization start
ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad4: 238475MB <Hitachi HTS723225L9A362 FCDOC30F> at ata2-master SATA300
ad4: 488397168 sectors [484521C/16H/63S] 16 sectors/interrupt 1 depth queue
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <Intel> at usbus5
uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <Intel> at usbus6
uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
ugen7.1: <Intel> at usbus7
uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
GEOM: new disk ad4
battery0: battery initialization done, tried 1 times
ad4: Intel check1 failed
ad4: Adaptec check1 failed
ad4: LSI (v3) check1 failed
ad4: LSI (v2) check1 failed
ad4: FreeBSD check1 failed
ata3: Identifying devices: 00010000
ata3: New devices: 00010000
ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
ata3: device_reset timeout=200us
GEOM_LABEL: Label for provider ad4s1 is msdosfs/DellUtility.
acd0: <MATSHITA DVD+/-RW UJ862A/1.02> DVDR drive at ata3 as master
acd0: read 4134KB/s (4134KB/s) write 4134KB/s (4134KB/s), 2048KB buffer, SATA150
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ata4: Identifying devices: 00000000
ata4: New devices: 00000000
ata5: Identifying devices: 00000000
ata5: New devices: 00000000
GEOM_LABEL: uhub0: 2 ports with 2 removable, self powered
Label for provider ad4s2 is ntfs/OS.
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
uhub6: 2 ports with 2 removable, self powered
uhub3: 6 ports with 6 removable, self powered
uhub7: 6 ports with 6 removable, self powered
ugen7.2: <USBest Technology> at usbus7
umass0: <USBest Technology USB Mass Storage Device, class 0/0, rev 2.00/1.00, addr 2> on usbus7
umass0:  SCSI over Bulk-Only; quirks = 0x0000
ugen3.2: <Dell> at usbus3
uhub8: <Dell product 0x2513, class 9/0, rev 2.00/a0.05, addr 2> on usbus3
ugen0.2: <Broadcom> at usbus0
uhub9: <Broadcom BCM2046B1, class 9/0, rev 2.00/1.00, addr 2> on usbus0
umass0:1:0:-1: Attached to scbus1
uhub8: 3 ports with 3 removable, self powered
(probe0:sbp0:0:0:0): error 22
(probe0:sbp0:0:0:0): Unretryable Error
(probe1:sbp0:0:1:0): error 22
(probe1:sbp0:0:1:0): Unretryable Error
(probe2:sbp0:0:2:0): error 22
(probe2:sbp0:0:2:0): Unretryable Error
(probe3:sbp0:0:3:0): error 22
(probe3:sbp0:0:3:0): Unretryable Error
(probe4:sbp0:0:4:0): error 22
(probe4:sbp0:0:4:0): Unretryable Error
(probe5:sbp0:0:5:0): error 22
(probe5:sbp0:0:5:0): Unretryable Error
(probe6:sbp0:0:6:0): error 22
(probe6:sbp0:0:6:0): Unretryable Error
GEOM: new disk da0
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <Ut165 USB2FlashStorage 0.00> Removable Direct Access SCSI-2 device 
da0: 40.000MB/s transfers
da0: 7712MB (15794176 512 byte sectors: 255H 63S/T 983C)
pass0 at umass-sim0 bus 0 target 0 lun 0
pass0: <Ut165 USB2FlashStorage 0.00> Removable Direct Access SCSI-2 device 
pass0: 40.000MB/s transfers
ATA PseudoRAID loaded
SMP: AP CPU #1 Launched!
cpu1 AP:
     ID: 0x01000000   VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00000400
ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 1 vector 48
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 1 vector 49
ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 1 vector 50
ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 1 vector 51
ioapic0: routing intpin 20 (PCI IRQ 20) to lapic 1 vector 52
ioapic0: routing intpin 22 (PCI IRQ 22) to lapic 1 vector 53
WARNING: WITNESS option enabled, expect reduced performance.
uhub9: 3 ports with 0 removable, self powered
ugen3.3: <Logitech> at usbus3
ums0: <Logitech USB Mouse, class 0/0, rev 1.10/4.10, addr 3> on usbus3
ums0: 3 buttons and [XYZ] coordinates
ugen0.3: <Dell> at usbus0
ukbd0: <Dell product 0x8157, class 0/0, rev 2.00/1.00, addr 3> on usbus0
kbd2 at ukbd0
kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000
ugen3.4: <Dell> at usbus3
uhub10: <Dell product 0x2513, class 9/0, rev 2.00/a0.05, addr 4> on usbus3
ugen0.4: <Dell> at usbus0
ums1: <Dell product 0x8158, class 0/0, rev 2.00/1.00, addr 4> on usbus0
ums1: 3 buttons and [XY] coordinates
uhub10: 3 ports with 3 removable, self powered
ugen3.5: <CN0TX5937248792401DW> at usbus3
ugen2.2: <Broadcom Corp> at usbus2
Trying to mount root from ufs:/dev/da0s1a
ct_to_ts([2009-04-28 09:55:51]) = 1240912551.000000000
start_init: trying /sbin/init
em0: Link is up 1000 Mbps Full Duplex
battery1: battery initialization failed, giving up